Ceiling under farmhouse
Reliable and without cracking.
The generally accepted structural movements are absorbed by the metal framework.
Differences in temperature and relative humidity do not cause dimensional variations in the plates.
BENEFITS
For new or old sites.
Low load under floors.
Integration of pipelines.
High performance.
Elimination of the risk of cracking
Ceiling on fur
(F530 or S47), plate
plaster in BA 13
mm. The frame on
frame or farmhouse
must be done with
screwed hangers (screws
of 35 for plate
plaster) or nailed (nail
galvanized) every
60cm maximum, between
axes of furs. The
along the fur, the
lines must be
at most every
1.20 m.
Diameter 8 brass plug, for the top of the diameter 6 threaded rod on concrete, solid slab .
High strength female anchor for concrete
Steel dowel diameter 8, for the top of the threaded rod diameter 6 on concrete, solid slab .
Drill: diameter 8mm
Or
Half collar (Constable hat)
Fixing for ceiling under slab, floor.....
Connection for the top of the threaded rod, diameter 6mm, smooth rod. Plugs 6 L 25
Steel piton dowel, for the top of the threaded rod diameter 6 on solid concrete slab
No dowel: quick and economical installation.
Reduced drilling diameter (diameter 5mm): time saving.
please wait for a few moments
Screwdriver adjustment: high torque and slow speed
Driving prohibited with a hammer (otherwise no resistance to tearing)
70kg
Factored load with a safety factor of 3 applied.
Using a chalk line, whatever the type of support, trace and set up the four corner hangers.
Laser faster and much straighter. Gradually put on the lines.
Secure the intermediate legs with the cord, put on the furs.
Tip. The profiles can be positioned using metal rulers.
A water level is made up of two graduated flasks joined by a pipe filled with water. It makes it possible to draw two points distant from each other on a perfectly horizontal line thanks to the principle of communicating vessels.
Wall bracket for mounting most laser levels. It allows multiple fixing possibilities. The height adjustment with locking device offers a very precise adjustment.
Connection: by wise clip or rotation on furs (S47 or F530).
Connection for the bottom of the threaded rod.
Max load 60 kg
Eclisse
Flatness and horizontality tolerances
- Framework and ceilings
General flatness: 5 mm under the 2 m rule. The ruler being kept in contact with 2 support points on the plate.
Horizontality: 3 mm/m without exceeding 2 cm.
- Ceilings
Local flatness: 1 mm under the 0.20 m rule.
Make the junction between 2 frames using a
splint and taking care to offset at least 1.20 m
the connections from one frame to another.
Eclistar S47 for ceiling furring
Ceiling frame fur
S47 - F530 length 3 or 5.30 m
please wait for a few moments
3D 2 ba13 ossature tout les 50 cm
Maximum height: 3.30 m
Remember to use pencil strokes against the wall, where the furs are.
Fur
Pencil stroke at the axis of the fur, before putting on the plate.
The plate lifter facilitates the handling of plasterboard
for ceiling installation.
Adjustable and lockable tilt angle.
Angle adjustment of the plate.
Possibility of tilting the plate beyond the horizontal
In order to make the joints at the end of the plate, fix the brackets corresponding to these joints 2 mm above the level of the other legs.
Clip the frames onto the legs. Place insulation if necessary. Screw the plates perpendicular to the frames.
All joints between plates must be aligned. (see diagram below)
0.60cm
Frame spacing for ceiling
0.50 cm max
NF DTU 25.41 authorizes poses
parallel and perpendicular to the frames,
the installation distances are as follows:
- 0.40 m in parallel laying;
- 0.60 m in perpendicular installation.
Insulation is allowed up to 15 kg/m2
0.40cm
